Hey fellas!
It's been long since our last blog...but worry not! Here I'm back again with something new to try this time around. This blog will let you know how to interface a 1.8 inches SPI TFT with arduino. The task may get a bit tricky if someone just starts without taking a few things in consideration. So here we go!
Now what's with this "SPI" term? Why not just a TFT?
Well, that's because like you all must have known, there are 2 modes of transferring data, SERIAL & PARALLEL. When there are separate multiple data buses for data transfer, that's a Parallel Data Bus TFT or more generally known as a normal TFT. These types of displays will have a comparatively large no. of pins to connect (quite obvious), as 8 or 16 pins are for data bus alone and then the other ones too.
They generally take up all the space on an UNO or even may require a shield as well.
When there is a single data bus to transfer all the data, all the data is streamlined in a series and then pushed towards the receiving end. This type of TFT is called an SPI TFT, where SPI stands for SERIAL PERIPHERAL INTERFACE. Now we know what that un-abbreviated form says!
Also remember that this 1.8 inches SPI TFT has different pin connections on an UNO (or similar) board and the MEGA board. On MEGA, the SPI pins lie at 50,51,52 and 53.
First of all, list of required items is as follows:
* Arduino UNO (or similar) x 1
* 1k ohm resistances x 5
* One-2-One connectors x 8
The TFT library comes pre-installed in Arduino version 1.0.5 and later.
Make the connections as mentioned below-
Reset
|
8
|
Dc (A0)
|
9
|
Cs
|
10
|
SDA
|
11 (UNO) or 51 (MEGA)
|
SCL
|
13 (UNO) or 52 (MEGA)
|
BKL
|
3.3v
|
Vcc
|
5v
|
Gnd
|
Gnd
|
Now instead of making the first 5 connections directly to Arduino, put a resistor of 1k or similar value between the TFT pin and the Arduino pin. That’s because the IO ports are 3.3v tolerant while the Vcc required is 5v. It is quite possible because of it’s non-standard chinese manufacturing.
Now, open the IDE and run the any sketch except the “BitmapLogo”. This sketch uses the SD card function and requires you to hook up the TFT with an SD card as well, which is definitely not a part of this article.
I’m putting a demo sketch that I ran successfully-
#include <TFT.h> // Arduino LCD library
#include <SPI.h>
// pin definition for the Uno
#define cs 10
#define dc 9
#define rst 8
// pin definition for the Leonardo
// #define cs 7
// #define dc 0
// #define rst 1
// create an instance of the library
TFT TFTscreen = TFT(cs, dc, rst);
// char array to print to the screen
char sensorPrintout[4];
void setup() {
// Put this line at the beginning of every sketch that uses the GLCD:
TFTscreen.begin();
// clear the screen with a black background
TFTscreen.background(0, 0, 0);
// write the static text to the screen
// set the font color to white
TFTscreen.stroke(255, 255, 255);
// set the font size
TFTscreen.setTextSize(2);
// write the text to the top left corner of the screen
TFTscreen.stroke(255, 0, 0);
TFTscreen.text("IoT Freaks!\n ", 20, 0);
TFTscreen.stroke(0, 255, 255);
TFTscreen.text("Sensor value\n ", 12, 25);
// ste the font size very large for the loop
}
void loop() {
// Read the value of the sensor on A0
String sensorVal = String(analogRead(A0));
// convert the reading to a char array
sensorVal.toCharArray(sensorPrintout, 4);
TFTscreen.stroke(255, 255, 0);
TFTscreen.setTextSize(5);
TFTscreen.text(sensorPrintout, 34, 50);
delay(550);
TFTscreen.stroke(0, 0, 0);
TFTscreen.text(sensorPrintout, 34, 50);
}
This sketch requires a sensor at pin A0 to read it's value and then display it as text on the TFT. So put any analog value sensor such as a potentiometer, an LDR, an IR pair or whatever you have.
#include <SPI.h>
// pin definition for the Uno
#define cs 10
#define dc 9
#define rst 8
// pin definition for the Leonardo
// #define cs 7
// #define dc 0
// #define rst 1
// create an instance of the library
TFT TFTscreen = TFT(cs, dc, rst);
// char array to print to the screen
char sensorPrintout[4];
void setup() {
// Put this line at the beginning of every sketch that uses the GLCD:
TFTscreen.begin();
// clear the screen with a black background
TFTscreen.background(0, 0, 0);
// write the static text to the screen
// set the font color to white
TFTscreen.stroke(255, 255, 255);
// set the font size
TFTscreen.setTextSize(2);
// write the text to the top left corner of the screen
TFTscreen.stroke(255, 0, 0);
TFTscreen.text("IoT Freaks!\n ", 20, 0);
TFTscreen.stroke(0, 255, 255);
TFTscreen.text("Sensor value\n ", 12, 25);
// ste the font size very large for the loop
}
void loop() {
// Read the value of the sensor on A0
String sensorVal = String(analogRead(A0));
// convert the reading to a char array
sensorVal.toCharArray(sensorPrintout, 4);
TFTscreen.stroke(255, 255, 0);
TFTscreen.setTextSize(5);
TFTscreen.text(sensorPrintout, 34, 50);
delay(550);
TFTscreen.stroke(0, 0, 0);
TFTscreen.text(sensorPrintout, 34, 50);
}
This sketch requires a sensor at pin A0 to read it's value and then display it as text on the TFT. So put any analog value sensor such as a potentiometer, an LDR, an IR pair or whatever you have.
Viola! I’m pretty much sure you’ll have it done then……
Be sure to buy the stuff mentioned in this blog by clicking on the link below-
http://www.ebay.in/usr/4d_innovations?_trksid=p2053788.m1543.l2754
The vendor's offering interesting and working hardware at quite handy rates. Go give it a try! :)
Be sure to buy the stuff mentioned in this blog by clicking on the link below-
http://www.ebay.in/usr/4d_innovations?_trksid=p2053788.m1543.l2754
The vendor's offering interesting and working hardware at quite handy rates. Go give it a try! :)
So until my next blog, this is it. As always, any problem you face and wish to discuss it, the comment boxes are always down there and you can reach me as well at iotfreaks@gmail.com.
For more of these interesting stuff, like my page-
https://www.facebook.com/iotfreaks/
And our community,
https://www.facebook.com/projectsdunia/
For more of these interesting stuff, like my page-
https://www.facebook.com/iotfreaks/
And our community,
https://www.facebook.com/projectsdunia/
) 
are ATmega8, Atmega16 and ATmega32. All these microcontrollers are belongs to ATMEL mega family. There are no difference between avr microcontroller. They only differs in memory size and Price.
r can measure the distance from 1" to 13 feet( 1 cm to up to 4metre) with accuracy up to 3mm. A hc-sr04 ultrasonic sensor has 4 pin GND, VCC, Echo and Trigger Pin. Trig pin generate an ultrasound by setting trig pin on the high state of 10 microseconds. Echo pin produce an output in a microsecond when ultrasound returns back from the object to echo pin.
)
)
or a photoresistor is a light dependent variable resistor that resistance decreases with the increase in the intensity of light. This gives an analog value so that it is connected to an analog pin of arduino board. A simple LDR is shown within the image and to buy an LDR click on the below image
